Normally we do not use data at wind directions of +/- 45 degrees from 180 (in sonic coordinates), in order to eliminate winds blowing through the tower and into the back of the sonic. Because However, because of the topography at RIM, I used data at +/- 60 about the nominal axis of the gap, SSW or 202.5 deg. The tilt plots are done with respect to the sonic u axis, which was pointed to 253 degrees. Thus in instrument coordinates, the acceptable data is from -10 deg to 110 deg.
Also at RIM, there is a systematic descent of air into the crater, i.e. a vertical flow normal to the "surface". I find more believable realistic lean angles by setting w.off = 0 and use the latter results in the RIM cal_files.Can recalculate these at end of project.9/29 00:00 - 10/15 00:00
sonic | lean (deg) | leanaz (deg) | w offset (cm/s) | ||||||
---|---|---|---|---|---|---|---|---|---|
3m.near | 0.5 6 | -3.2 .7 | -1 2 | ||||||
10m.near | 1.0 | 12 9.3 9 | -2 | ||||||
15m.near | 0.5 | 48 43.7 2 | 0 | ||||||
20m.near | 0.6 | 28 27.7 8 | -2 1 | ||||||
25m.near | 1.0 | 78 79.8 1 | -1 | ||||||
30m.near | 0.7 | 39 38.5 1 | -2 | ||||||
35m.near | 0.8 7 | 110 112.5 2 | -1 2 | ||||||
40m.near | 0.7 6 | 92 96.0 2 0 | 1 | ||||||
45m.near | 1.2 1 | 47 33.7 | -1 | ||||||
50m.near | 0.9 8 31 | 34.8 0 | 0 | ||||||
5m.rim | 1.5 -104.7 -3 |
| 1.3 | -96.5 -91.2 | 0 | ||||
10m.rim | 3.1 | -135 2.2 | -14 |
| 2.1 | -132.2 122.7 | 0 | ||
15m.rim 2.8 | -132.2 | -20 |
| 1.4 7 | -124107.3 5 | 0 | |||
20m.rim 2.8 | -136.9 | -22 |
| 1.2 4 | -135109.9 7 | 0 | |||
25m.rim | 2.8 | -146.4 | -25 | 1.1 | -119.2 |
| 1.0 | -161.5 | 0 |
30m.rim | 3. 1 -146.8 4 | -26 |
| 1.3 | -158.9 126.2 | 0 | |||
35m.rim | 2.8 | -139. 1 | -30 |
| .2 0.8 | -139101.1 4 | 0 | ||
40m.rim | 4.0 | -132.7 | -31 |
| 2.0 4 | -125110.3 8 | 0 | ||
3m.far | 1.0 1 | -2931.1 8 | -1 2 | ||||||
3m.flr | 0.6 7 | 166 162.2 1 | -3 | ||||||
3m ssw2.ssw2 flr | 10.3 1 | -59.4 0 | 3 2 | ||||||
3m ssw4.ssw4 flr | 30.5 | -38.0 2 | -5 |