Burnin tasks

Feel free to edit and expand.

(At some point, we will want to start soil core sampling, but perhaps this can be considered an Ops task...)

S1 - Station 18

• Site photos
• Dsm port caps
• Verify ground braid from dsm to ground rod
• Plug boom holes with putty
• Recheck guy wire tension
• Add soils (two sets)
• TRH not reporting - replaced SHR
• Ott not reporting - replaced Ott, switched long cable to 5m so we have a spare long cable
• Check out sonic orientations - directions offset between 2d and 3d - both are mounted in same way as other towers
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable
• Replace 1A fuse to serial board with 2A
• EC150 reporting nans for h2o/co2 - back on its own, must have been the fog
  

S2 - Frinj Coffee

• Site photos
• Dsm port caps
• Plug boom holes with putty
• Verify ground braid from dsm to ground rod
• Recheck guy wire tension
• Investigate solar assembly (see 3/19 blog post)
• Investigate cell antenna?
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable
• Replace 1A fuse to serial board with 2A
• Gsoil upside down - fix in calfile

S3 - El Capitan

• Site photos
• Dsm port caps
• Plug boom holes with putty
• Verify ground braid from dsm to ground rod
• Recheck guy wire tension
• Add soils
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable
• Replace 1A fuse to serial board with 2A

S4 - San Marcos

• Site photos
  
• Dsm port caps
• Add sign
• Verify ground braid from dsm to ground rod
• Plug boom holes with putty
• Recheck guy wire tension
• NR01 not reporting - plugged into .cr mote, switch it over
  
• Victron not reporting - needs USB cable?
• Very large timeoffset values - check on chrony?
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable
• Replace 1A fuse to serial board with 2A
• Investigate GPS - bad time sync, reseat GPS antenna?

S5 - Exxon

• Site photos
  
• Dsm port caps
• Recheck guy wire tension
• Plug boom holes with putty
• Verify ground braid from dsm to ground rod
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable
• Replace 1A fuse to serial board with 2A

S6 - Hazard

• Site photos
• Dsm port caps
• Recheck guy wire tension
• Plug boom holes with putty
• Verify ground braid from dsm to ground rod
• Off the net since 3/20
• NR01 not reporting
• Tsoil not reporting (from blog post)
• Investigate cell antenna? - added directional antenna
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable
• Tsoil not reporting - replaced tsoil
• Number of satellites not reported - GPS problem? - GPS recording fine by the time I visited

S7 - Reagan Ranch

• Site photos - still need manfrotto photos when done 
  
• Tape over light on dsm
• Install manfrotto, NR01 - still need nr01 mounts
  
• Dsm port caps
• Recheck guy wire tension
• Plug boom holes with putty
• Verify ground braid from dsm to ground rod
• Mote is responding but none of its sensors are - soils reporting after scanning i2c
• Check for 3 TRH crossarm mounting bolts - 3rd hole not threaded, found a nut that will work
• Install Y power cable
• Replace 1A fuse to serial board with 2A

S8 - Santa Ynez

• Site photos
• Tape over light on dsm
• Verify contact info is on dsm
• Dsm port caps
• Add sign - no
• Recheck guy wire tension
• Plug boom holes with putty
• Verify ground braid from dsm to ground rod
• Off the net since 3/16
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable
• check  if dsm watch network script installed - yes
• TRH not reporting - replaced both probe and housing
• PPS sync failed, getting large time sync offsets

S9 - E. Camino Cielo

• Site photos
• Contact info on DSM
• DSM port caps
• Tape over light on dsm
• Verify contact info is on dsm
• Dsm port caps
• Add sign
• Recheck guy wire tension
• Plug boom holes with putty
• Verify ground braid from dsm to ground rod
• USB cable for victron
• Sticker for camera
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable
• Replace 1A fuse to serial board with 2A
• Lambda giving bad values - negative or highest of all stations
• Off the net for 7 hours, investigate

S10 - La Cumbre

• Site photos
• Tape over light on dsm
• Verify contact info is on dsm
• Dsm port caps
• Add sign
• Verify ground braid from dsm to ground rod
• Plug boom holes with putty
• Recheck guy wire tension
• Check out sonic orientation - wind direction offset between 2d and 3d - same setup as all other stations
  
• Install soils
• Victron not reporting - add USB cable? - Cable was already there, needed to ddn/dup to get it to show up as USB device
  
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable
• Replace 1A fuse to serial board with 2A
• TRH not reporting - reporting again by itself, maybe investigate when there?

S11 - Montecito

• Site photos
• Tape over light on dsm
• Verify contact info on dsm
• Dsm port caps
• Add sign
• Recheck guy wire tension
• Plug boom holes with putty
• Verify ground braid from dsm to ground rod
• Install soils
• Investigate cell antenna? - tried but didn't find a good solution
  
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable
• Replace 1A fuse to serial board with 2A
• NR01 needs fan cable
• Remove omni antenna? Was on the net more often without it
• GPS number of satellites low (don't know what to do about this)

S12 - Gaviota

• Site photos
  
• Tape over light on dsm
• Verify contact info on dsm
• Dsm port caps
• Add sign
• Victron not reporting - add USB cable? Yes, missing cable
• Verify ground braid from dsm to ground rod
• Plug boom holes with putty
• Recheck guy wire tension
• Add tripod? Mote/NR01/soils not reporting, don't know if they're there. - added tripod, nr01, bender to bulgin cable
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable
• Replace 1A fuse to serial board with 2A
• Off the net almost 24h, presumably not modem problem

S13 - Boy Scout Camp

• Site photos
• Dsm port caps
• Add sign
• Verify ground braid from dsm to ground rod
• Plug boom holes with putty
• Recheck guy wire tension
• Rfan reading very different than other sites, replace TRH housing?
• No lightning rod - do we need to add one?
• Second set of mote/NR01/soils not responding, is it installed? - not installed 
• Investigate cell antenna?
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable
• Replace 1A fuse to serial board with 2A
• dsm giving under voltage errors. Replace pi power cable or dsm?

S14 - Sedgwick

• Dsm port caps
• Add sign
• Verify ground braid from dsm to ground rod
• Recheck guy wire tension
• Plug boom holes with putty
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable
• Replace 1A fuse to serial board with 2A

S15 - Figueroa

• Site photos
• Dsm port caps (Steve installed)
• Contact info on dsm
• Verify ground braid from dsm to ground rod (Steve installed)
• Plug boom holes with putty
• Recheck guy wire tension
• Add manfrotto tripod: need to bring tripod, NR01 + wetness sensor + fan cable + boom + tripod plate
  
• Add bulgin cable (15m+) to mote, cable sheathing too
  
• Needs a TRH crossarm mounting bolt
• Replace 1A fuse to serial board with 2A
• Gsoil not reporting - now whole mote not reporting? - brought back mote by reseating bulgin connection to dsm, brought back gsoil with scan i2c

S16 - Little Pine

• Tape over light on dsm
• Verify contact info on dsm
• Site photos
• Dsm port caps
• Add sign
• Verify ground braid from dsm to ground rod
• Plug boom holes with putty
• Recheck guy wire tension
• No co2/h20 reported, bad EC150? (just large offsets.  cleaned, but didn't change offsets)
• Add knuckle to ground rod (?, blog didn't mention adding it but it may have been done at second visit)
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable (forgot to bring)
• Replace 1A fuse to serial board with 2A (already had 2A)
• TRH not reporting (was okay at the time)

S17 - Cuyama Peak

• Investigate -273s from tsoil (presumably cable unplugged) (was loose connector)
• TRH intermittently goes out. So far pio brings it back up, but consider replacing if there.  (Totally dead when there and needed to be totally replaced.)
  
• Recheck guy wire tension (one inner guy somewhat loose)
• DSM port caps (needed one)
• Check for 3 TRH crossarm mounting bolts
• Install Y power cable (Yes, still need to do)
• Replace 1A fuse to serial board with 2A
• Clean EC150 lenses

S18 - Windermere

• Dsm port caps (needed)
• Verify ground braid from dsm to ground rod (okay)
• Plug boom holes with putty (was done)
• Recheck guy wire tension (were good)
• Check for 3 TRH crossarm mounting bolts (1 missing, but mast hole plugged)
• Install Y power cable
• Replace 1A fuse to serial board with 2A (only had a 3A, so used it)
• Site pics